
| HOW I SETUP MY ELECTRIC GUITARSA General Guide to Getting High Speed out of an Electric Guitar |
| The electric guitar is one of the most adjustable analog musical instruments you can get your hands on. In contrast to acoustic guitars especially. You might have noticed there's all sorts of screws and springs all over the darned thing (and maybe some you have not noticed yet) to allow you to setup everything having to do with action, intonation, neck relief, how the vibrato feels/stays in tune.
One of the most useful pieces of knowledge I taught myself doing this for almost 30 years, is that setup is a huge game of angles. Every tiny, minute, we're talking fraction of a millimeter, that you change, can make sometimes a very huge difference and can make or break a setup. The more sensitive or more extreme the music you are trying to play, the more precise you need to be. If you're just strumming cowboy chords on 12s on a neck pickup only hollowbody, it's going to need to be be less as precise than say...me doing whammy bar dives and playing 64th notes at 185bpm on a Fender Jaguar while crunching up the bridge pickup with double the gain of a 70's "dino" player....a real challenge actually. Another huge key, is using the instrument's design to your advantage for the best setup. Part 1 - ASSESSMENT, FIGURING OUT WHAT'S NEEDED The first thing I consider, is the guitar that I'm dealing with. And the first thing I notice, and this goes against every fiber of my being, is potential judgement of who owns/owned that guitar before. Was it a beginner who sold it when they got a Les Paul? Was it a intermediate guy who tinkers like me as well? If so, how well was the tinkering done? Does it look abused or wrecked? Did their lover throw it/hit it with a hammer/damage it/pour liquids on it? Did I find it in a dumpster, a pawn shop, or at a music shop? Does it seem likely the neck will need replaced? Is it a 90's or older Eastern build made of plywood to a cost point? Or is it a high end guitar with a track record of being consistantly good (*sigh* I wish). CreepingNet's first rule of "Cheap" guitars or even "GSOs" (Guitar Shaped Objects) is that the amount of money spent is relative to the amount of TIME you'll spend making it good. It's not mutually exclusive EVERY time, but it is a good rule to follow. This is how most guitar repair shops work. However, since I'm not a repair shop, and I genuinely enjoy doing this stuff - enough I'll sometimes just pick some random guitar from my collection on a random Saturday to do a setup on as a "relaxation" activity - then I'm willing to put in the work when nobody else will. At the lowest tier is mid 2000's (say, circa 2005, when the cheaper Asian builders started getting on their "A" game - ie Taiwan, China, Korea, Indonesia) all the way back to 1960's Japanese guitars, or 1970's mainline brands (Fender, Gibson). These are the guitars that have the most mistakes at the factory, and where it seems a lot of the "Design" process was just generate something that looks like what it's supposed to look like and slap the parts at the factory on it. And by mistakes we mean anything as minor as a slightly too deep neck pocket that needs a shim, all the way to a complete wreck with a misplaced bridge, uneven frets with incorrect spacing, a nut cut too low or too high, tuners that need pliars to turn within 2-3 years, and routing that seems like it was done by a blind, drunk guy. The mistakes that need addressed before even considering a setup - as in MUST BE - is a misplaced bridge (it happens), a neck with bad fret slot placement (I'd replace the whole neck honestly, since it's most likely bolt-on - and for me to get something like that, it has to be sold to me for under $50 or given to me), neck slot that's cut too high (it's not a good sign if I'm maxxing out the bridge/bridge saddles with a decked neck just to stop the strings from buzzing) - which also could be un-even frets (we'll get to that in a moment). Some things like janky routing of the electronics or whatever are signs, but they aren't the problem, just ignore that crap. Guitar abuse is pretty rampant, especially on electrics (Acoustics don't survive it). Part of this is people who go into doing the things I do, without understanding what the hell they are doing first. It's easy to read articles of people like me without a paragraph like this and think to yourself "hey, I can do this" but you still don't UNDERSTAND WHY you are doing it. I've had my share of cheap electrics with needlessly maxxed out truss rods, weird attempts using hand tools to correct design issues (ever had a neck slot that tapers DOWN towards the bridge and has tooling marks from chisels? - NIGHTMARE). I don't consider wear and tear abuse, but an idiot with chisels and an electric guitar can be a real problem. I know, I was that guy - my Kramer is proof, lol. Don't knock down the retaining wall for a recessed floyd (however it did even out when I came up with a reinforcement method for those). So if you fuck up, don't feel like it's the end of the world either, there's always extra sturdy wood, Titebond II, and 24 hours. Lastly, expensive doesn't mean nice. I wouldn't have bought my 71' Musicmaster body and neck if they were asking any more than they were. Together, a 71' Musicmaster is a more than $500 guitar. But in pieces, I'm not going past $250. And it had one of the CBS Fender mistakes on it - the body had a neck pocket that was cut too wide at the factory. Of course I corrected that, that's why it's my Jag-Stang's backup. However the neck on it is a work of art, as good as my MIJ Jag-Stang's neck is. Low, fast, frets are level, and the profile is identical. Anyway, enough of my chatter, regardless, let's get these things setup...Part 2 - NECK STUFF (TRUSS ROD, SHIMS, FRET LEVEL, NUT STRING HEIGHT, etc...) I usually start with what the neck is doing. This is the most misunderstood, miscalculated part of the guitar. It's also one of the most negelected outside the back profile I feel. We're talking about a long, thin, assembly of wood, with a 1/4" rod (or rod assembly) acting as a counterbalance for between 60-220LBS of metal wire tuned to pitch and trying to yank that piece of wood back toward the bridge as a result. The first thing I do is check the neck relief. Ideally, a guitar neck is 100% straight. No, this isn't a sexual question, it's a GEOMETRY question. And that's why I usually start with the truss rod. It's also the most boogered up thing. For almost a century, so-called "luthiers" have been telling you it's "dangerous" to adjust the truss rod, or you could "damage" the guitar - well, you could damage it adjusting the bridge saddles if you do something stupid enough. I have two ways to check this, one is to buy a special ruler with notches cut into it for your scale length, another method is to press down or put a capo on the 1st fret, then press down at the last fret, and see how much of a gap you have between the strings in the middle of that length, and the top of the fret in that area - where it's highest. For me, that's usually around the 7th/8th/9th fret area but can be as low as the 5th or as high as the 11th depending on the truss rod used, which end the adjutment is on (there's a dead zone at each end of the fretboard for relief as a result of the area where the truss rod is locked in, and the area where the truss rod adjustment mechanism is located, usually about 1" at each end). If there's more than a business-card thickness of that area, then you probably need to tighten the truss rod, if there's NO relief, or even, if it seems the string is high centered on the fret (could be really bad), then you need to loosen the truss rod. After that, take the strings off, take the neck off (if you can), and check the straightness of the neck with the strings off in the same range using the special ruler, or you can use a straight edge over the top of the frets (assuming they are decently level enough), and the gap between the fretboard and the straight edge should be about the same across the board, and any gaps between frets and the straightedge (in this case my aluminum yard stick) will also reveal fret leveling issues. If the gaps are uneven and the frets, then you're looking at a possibly badly milled fretboard, and if it won't lay flat, and you unscrew the truss rod until there's no tension on it, and it's still got a "backbow", then you have a warped neck. Newer import guitars can have this backbow taken out by turning in the opposite direction (assuming Bi-Directional Truss Rod, which is basically the standard now - you'll know because the nut wont come out, but rather, gain tension in the other direction), but older models might be salvagable by unscrewing the neck and letting it sit awhile without tension, or in extreme cases with a forced upbow to recondition the wood to rest in a more "relaxed" position. Once the neck is straight, it's time to check the frets. I do this nowadays using a Fret Rocker tool, but I used to use any flat piece of metal I had laying around to test for uneven frets back the olden days before I had money. If the frets are uneven, and I have the tools, I'll level and recrown them. I got a cheap-ass Amazon fret leveling kit for my last birthday and it's been a game changer, just about every guitar in my house now has crazy-low, fast, action on it. We're talking 1.25mm at the 12th fret low. The frets being level is a VERY important part of getting your action right. Uneven frets leads to fret buzz or even the next fret playing in some spots (with really bad fretwork). But you MUST make sure the neck is 100% level before you do this for the best results. Leveling the frets is basically taping off the fretboard, or using fret protectors, and marking the frets with a magic marker (or if you are a skilled drawer like I am you can get away without, but you run the risk of marking up your fretboard that way so I don't reccommend it to most people). Then you use a very fine fret file or sanding beam and do a few to a handful of passes with the block doing the weight of the job, and then see where the high and low spots are. High spots will have the marker sanded off and reveal bare metal, while the low spots are still marked. After that, I note any areas where those high spots are to recheck later and then continue sanding till the marker just comes off the low spots. I work side to side to make sure I'm keeping the height even all the way across the neck as well as up and down. On some guitars with a rounder fretboard radius - such as Fenders with a 7.25" (ie my Jaguar, Musicmaster, Jag-Stang, and some others), I might even make a few extra passes down the CENTER of the upper frets to allow slightly lower action without choking out on huge bends (if you're gonna' go all John Sykes on a Jag-Stang, you have to consider Leo Fender's choice of radius for 24" scale necks in the sixties). I don't want to take off more than a fraction of a millimeter or a few at most - just enough to not alter the radius in a noticeable way, but to allow the strings to pass over the midsection of the fretboard. Not just have I done this to my Jag-Stang, but Colin of CSGuitars on YouTube did this to a Jag-Stang as well with the same results. With all that squared away, let's take a look at the bridge, nut, and how they relate to the fretboard area... Part 3 - PRELIMINARY NUT/BRIDGE/TAILPIECE STUFF (STUFF TO CONSIDER) Now that the neck is straight, frets are leveled and recrowned, and polished...we're getting deeper into the geometry here. The first thing to consider is your STRINGS, particularly, the gauge, and maybe composition. Guitar strings can go from a very light .007-.038, all the way to a .014-.060 gauge set. Each string pulls with the force of between 6lbs, and 30LBS of pressure, and collectively can range from 70LBS total, to 188LBS or more. Heavier the gauge, the more stress on the components, and the more reinforcement needs to be considered. Different brands have different tension as well, Earnie Ball Super Slinky's are going to be way less tensioned than a set of Fender Bullets for example - even in the same genre of gauges. Most of the time, I live in the happy area of .009-.042 gauge for myself, because I play fast, precise things, and because I'm getting up there in my years, with a good setup, it takes way less effort to play the guitar, and makes the effects of aging less of an issue, to a point where it's irrelevant pretty much. I'm 43 and ripping Master of Puppets main riff better than I ever did at 23, because my guitars are better setup, and therefore, the effort I put in needs to be way less than back when I was playing with about 2mm at the 12th fret and I thought hammering into the string with the force of a elephant with a Dunlop Jazz III (and most likely a less fluid, tighter grip and as a result movement) was "the way". Nobody wants to admit it, but a lot of "metal" guitar playing, especially thrash or groove, is best done with a delicate, tactful touch on an exceptionally setup instrument. It just doesnt sound "aggressive" enough. And there is a way to get that aggressive attack without the constitution of a stone statue, but that's a skill/playing/lessons thing, not a setup thing. Setup is just one part of it. Alternative/Grunge guys didn't need low action (go look up J.Mascius) because "speed" wasn't a part of the equation, they wanted it just to play well enough to be comfortable on stage without having to think about it too hard. So, I restring the guitar, and start assessing the string height at the nut, and the bridge saddles by dropping the bridge(s) down overall until things start to buzz, then setting slightly up. I picked this up reading the Wolfgang manual Edward Van-Halen wrote, lol. It works. One thing I want to pay attention to, is the maximum and minimum height of the bridge first. It's possible the neck slot was cut too deep, and the neck might need shims to sit at a apropriate height to give low enough action to be playable. I see this quite a bit with older Strat copies and simliar with bolt-on necks. A real piece of shit though is a glued-in neck that's in a flat position, and then the bridge used is too high to get good enough action for lead guitar without modification. That's a nightmare, and time to consider really modifying the guitar (we're talking routers, drills, creative decisions, and refinishing here). Luckily I've only encountered this issue with one gutiar - a Squier Double Fat Tele Deluxe. Fender didn't put enough "meat" on the fretboard to allow the strat saddles to nearly slap the strings against the frets - saddles all the way down was about 2mm at the 12th fret, my Squier CV 70's Jaguar has lower action than that with no shim from the factory with my own fret level/recrown and it RIPS like a Ibanez Jem. With a bolt-on though, I just shim the neck. I'll use whatever is handy, but my favorite material is the plastic used in vacuum-form packaging for things like batteries and whatnot. I'm not spending $40 on a pack of wood "shims" for a guitar that costs double that. Also, there's so much snake-oil in this industry it's hilarious. I've been using plastic shims I make myself since 1997, and it's worked for me just fine. People say not to use paper products, I find they are actually good if you overshoot the intended angle a little, as it will settle into a nice place. But that's not a pro-trick, that's me working with what I have. Next, I check at the nut to see if the string slots are cut too high (they often are on cheaper guitars), but that's better than cut too low, because you need to either refill the slots and start over (cheapest), shim the nut if it's a Floyd Rose locking nut, or do some woodwork in the opposite with a Floyd (ie filing the shelf lower), or replace the nut overall. I usually want roughly 1/2mm to 1mm - about a business card oddly enough - between the 1st fret and the open string. The key thing with the nut is the action cannot be lower than the nut is if it's too high (or ALL of the string will buzz/fret out), but you can't make the action too low at the 1st fret, or it's going to mean you have to crank the bridge higher up to clear the frets going forward with the opposite problem. The best is to get it as "even" as you can. Usually for me, that's around 1/2mm-1 3/4mm at the nut, and then I end up with between 1.25mm to 1.5mm at the 12th with no buzzing, choking, or noise. That's usually where I set my action at. The most important thing is to set the action BEFORE you set the intonation. That's how you get very accurate intonation, and with Electric guitars, this is way more important than with acoustic guitars. Acoustics have overtones that electric guitars don't have that can hide - what we're now calling in the industry "audio data" that would be considered unfavorable if it wasn't being masked. So it's important to nail the intonation on the guitar as well as you can. Once you have it set, there is one piece to talk about in-between - Vibratos (or Tremolos in Fender terminology), ie, that bar sticking out of the top that makes the strings do the "war war war" thing as the old folks call it, lol.Part 4 - GENERAL VIBRATO CONSIDERATIONS, FRICTION IS NOT YOUR FRIEND! Okay...so now let's talk about Vibrato Systems, because I think they are the most misunderstood thing on electric guitars, and some people think Floyd Rose is too hard and vintage units don't stay in tune...it's all bullshit. I've had MANY vibratos in my 30 years: Floyd Rose, Strat Trems, 2-point Strat Trems, Kahlers, Floating Jaguar/Jazzmaster trems, Dynamic Mustang Whammies, Weird home-built shit, Guyker stuff that works like a Steinberger almost...and they all have some common issues. The first problem nobody talks enough about is how you STRING the guitar. A lot of people restring their own guitar, and I can't blame em', it's expensive to have a shop do it on TOP of the higher string costs today. But not a lot of people talk about how you wrap the strings or attach them to the tuners (and how many wraps) affects tuning stability. The industry tries to push all sorts of shit on people every year from locking tuners, to new locking nut designs, just to sell you another thing to keep your guitar in tune. Some work, some don't, but that's just throwing money at the problem, not fixing the root of the problem - how you string it. I use $50 sets of Klusons to replace the stock tuners once the stock tuners stop doing their job well. And a lot of times, stock tuners are more than good enough, especially anything made after 2005. The first problem that everyone argues about is getting the strings to stay on the capstans. My favorite machine head capstan style is the "Split Shaft" Kluson used in the 50's-60's - almost all of the original Fender guitars and some Gibson guitars from that time, also Rickenbacker too, had these. I think Part 5 - FINAL ACTION SETTING & INTONATION |